Motor-unit DNP-2021.
Especially made for Nouvelle Platine Verdier
First.
Many owners of the Nouvelle Platine Verdier
turntable have mailed us regarding their Verdier
Motor-unit. Many problems have been mentioned.
Could we help?!
Well …..
We at Micro-Seiki.nl are now very proud to announce
that Dereneville from Germany made a new Motor-
unit exclusively for owners of Nouvelle Platine Verdier
Turntables. The design is based on the original
Motor-unit made Verdier, but the Technic is much
more advanced.
General.
•
For the Papst synchronous motor (Type: VDC-3-
43.10 937 4310 602), a newly developed and
perfectly resonance-optimized housing was
developed. Weight: 2.5 kg. (Papst = Name of the
brand)
•
Four freely selectable speeds - 33.33 RPM - 45.00
RPM - 78.00 RPM and one extra speed 16,66
RPM.
•
Dimming the display. The dimming values are
freely programmable.
•
Pitch Control in 100th, 10th, or in whole
increments, within the given speeds of the Papst
engine.
•
Custom, freely programmable acceleration and
deceleration ramps for different turntable
masses, including soft start.
•
Input for an external tacho signal from the
turntable, to form a precise, closed loop for
maximum synchronization accuracy.
•
Free programmable motion animation from 1 h
to 168 h means: automatic, gentle soft start and
short run of 1 min.
•
All parameters can be programmed freely using
the buttons and display on the display, or quite
elegantly with the help of a PC via a USB-II input.
•
The internal memory allows the allocation of
three individual and independent memory sets -
For example, to use three different drives, to
change belts to tape or string, or to alternate use
of 3 tonearms / pickup systems.
•
At every time available operating hours – 11
pieces at the number - of the individual sets
(system runtime, etc.)
•
Power supply 24 VDC. The complete electronic
control is housed in the compact drive unit.
More specific.
The new Dereneville DMS-5001 Tribute Motor-unit
offers a unique perspective and user flexibility in
turntable motor units. All operational parameters can
be set by manually using the push buttons on top of
the drive unit.
Additionally for convenience, the parameters can also
be programmed via computer, with the aid of our
specially developed software.
The housing of this drive unit, made from high grade
Aluminium, is specially designed for the Papst-
Synchronous motor VDC-3-43.10 937 4310 602 which
allows for a vibration free and low noise operation,
thanks to the flexible mounting of the motor itself
inside the housing.
The complete electronic control unit is safe and EMV
tested and is integrated in the housing. The
integrated display shows every status and each step
during programming by the buttons on top. The
brightness value is user adjustable as is the delay
time for illumination decay.
This new developed drive unit offers three speeds:
33,33 rpm / 45,00 rpm / 78,00 rpm and one hidden
speed: 16,66 rpm and a pitch control over a very wide
range whilst the turntable is running.
This hidden speed of 16,66 rpm offers two
advantages: firstly, you can play the old records cut
by 16,66; secondly, it lowers the platter to half speed
in order to change the record more safely whilst
running. By pushing the 33,33 knob once, the speed
goes down to 16,66 - and by pushing it again, it will
speed up to 33,33 rpm.
All speeds can be calibrated with exacting precision in
very small steps 1,0 / 0,1 / 0,01 or 0,001 Once the
speeds are calibrated, they can be stored in the
memory of the electronic board. This is possible for
every Set.
Usually you only have to adjust the main speed 33,33
rpm. The electronic control unit inside calculates all
other speeds exactly. Of course, you can check them
and calibrate them individually.
The main memory is fragmented in three segments,
called: Set 1 / Set 2 / Set 3. This means, that you can
illustrate three different, virtual drive units in just
one.
For example: if you have up to three turntables,
then you can use only this one drive unit to play
them perfectly, each at a time. Just place the
drive unit to that turntable you want to play and
recall the set for this turntable. The hours of
operating of the three sets will be counted
separately, together with the total hours of drive
play.
Each Set has its own operation hour control and
supports the belt and up to three needles. In
practice: if you have two or three tone arms mounted
at your turntable, all with different cartridges, you
can assign them to (PU: Pickup) PU 1, PU 2 and PU 3.
This means, that you can monitor operational
duration of a single or multiple cartridges, every time
you want. This is a useful application to determine
stylus degradation over time.
You can, for example, program a user-defined time
period for oiling the bearing of the turntable. This
drive unit will store this and implement it for you.
Moreover, you will get the exact time to change the
belt or string in the preselected time.
Different turntables have different platter weights.
Our drive unit offers the best possible approach to
generate the perfect time for accelerating and
decelerating. This preserves the belt or the string
from damage. All values can be programmed
separately in each set and they can be stored in the
main memory of the electronic unit and also on your
computer.
This unique feature, along with the other
applications, are suitable to programming via
computer. The connection has to be made via USB-II
cable.
Our -motion animation- means you can program any
number of individual times from 1 hour up to 7 days
to run the turntable, for example 1 minute or more,
at a lower speed. This ensures that the oil in the
platter bearing will be evenly shared and the belt or
string will find another position, preventing damage
to the turntable and belt.
This drive unit works only with 22 to 24 VDC. A special
analogue Power supply is installed in the housing.
The complete electronic control unit is integrated on
board the drive unit.
This high-end drive unit is manufactured and
assembled in Germany and conforms to RoHs
standards and correlates with the European CE and
the FCC in the United States.
365,00 Euro
(Brass version; Including
Shipment)
275,00 Euro
(Aluminum version; Including
Shipment)